#Ista d setup how to
#Ista d setup manual

Performance tests of CO catalytic converters. Performance tests of CO catalytic converters

#Ista d setup how to

How to use test module of the Lambda probes What to do?Ī Stratified charge doesn’t reduce fuel consumption?į10/11. Stratified charge performance checkį10/11. The problems of the injectors and misfiresĬar with N57N engine and very low mileageį10/11. Re-adapting of the automatic transmission What other problems can be caused to my car by hidden problems of the NOx system?Īre there any ways to see the “health status” of the NOx system?… What are the main differences between NOXEM emulator and ‘’usual’’ emulators?įuel consumption of my car has increased, but DME has no error messages recorded. What is the difference between NOXEM NOx emulator and OEM NOx sensor? After confirmation of deleting the adaptations (by pressing ‘Continue’ after the warning ‘Adaptation values will now be reset’), the message ‘Switch off Terminal 15 and terminal R’ appears.

press the ‘Start / Stop’ button several times while all the indicators (ABS/DTC, SRS, etc.) light up in the KOMBI.Ĥ.

do not press any pedal (no clutch, no brake pedal).

How to comply with ‘Ignition ON’? – my car does not have an ignition key, it is equipped with the Start / Stop button. The reason: the condition ‘Ignition ON’ is not met, see p.3ģ. After confirmation of deleting the adaptations (by pressing ‘Continue’ after the warning ‘Adaptation values will now be reset’), the message ‘Could NOT reset adaptation values’ appears. If communication between the car and ISTA D/+ is established, the car’s basic data will be read from the car.Ģ. Contact interface vendors to resolve the issue.

Typical problems with OBD / USB host or ICOM IP address and port settings. The reason: communication problems between ISTA D/+ and the car. Menus relating NOx sensor and NOx converter are not accessible. When starting a session with ISTA D/+, basic data of car does not appear on the computer screen, they must be entered manually. 300 km), check the new adaptations and clear error message memory using INPA or ISTA D/+, if necessary.ġ. 8 driving sessions for cold/warm engine, at least 200.

*these error messages in the exact situation do not indicate any problems with the engine performance.Īfter new adaptations are completed (after 5.

uneven run (Stratified charge and/or Homogeneous injection).

insufficient performance of CO catalytic converters.

error messages relating fuel trim (bank and/or cylinders individually).

Solution: turn on ignition, press and release accelerator pedal for 3 times, then start engine.ĭuring adaptation process (after old adaptations have been cleared) some error messages* can appear: Note: when adaptations are cleared, following error messages* can appear immediately:

With this, the creating of initial adaptations can be considered as complete. Next few times, when starting the cold engine:Ī) allow the engine to run idle at least for 5 minutes ī) drive with longer driving sessions with even RPM and torque when possible. Recheck error message memory, clear if necessary.ġ2. 10 seconds Į) stop the car, switch off the ignition, takeoff the key, disconnect the diagnostics cable į) wait, till the lighting of start/stop button turns off.ī) allow the engine to run idle for 5 minutes Ĭ) perform the driving session with even speed 60.

#Ista d setup manual

110km/h on even road Ĭ) switch the 4th gear (for automatic transmission – in manual mode) ĭ) release the accelerator pedal, brake with the engine (don’t press brake pedal) for 7. slowly press and release accelerator pedal for three times ī) accelerate till 100.turn off the engine turn on the ignition.If ISTA D/+ does not displays notice “Adaptation values and taught versions were reset” after the attempt to delete the adaptations, repeat the procedure once again.Īttention: the car may run unevenly! If EML (check engine) symbol appears on KOMBI and increased/incorrect idle is observed: Select Reset adaptation values and versions (encoding)įollow the instructions very carefully! If deleting of adaptations was successful, you will see notice “Adaptation values and taught versions were reset”. Select Delete engine adaptation value, press Displayĩ. open sub-menu Power train, press Start search:Ĩ. Start new session in ISTA D/+, perform the identification of vehicle and a test:Ĥ.

Ista-d setup